System designers are faced with many obstacles during the design of a smartphone or tablet, one of the toughest being integration of key components such as display bridges. QuickLogic’s CUB (Customer Use Board) system allows designers to insert QuickLogic’s ArcticLink III VX CSSP series of display bridges into the display path of their product, allowing software bring-up and product testing to take place through known-good hardware.
During the design process, often physical CPU reference design boards are used for testing and bring-up of prototype hardware. These reference designs are subject to the specifications of the processor, meaning often they only support a single display standard (MIPI-DSI, LVDS, or RGB, for example). As has been shown numerous times through millions of shipping products, often the display chosen requires a different standard, and a bridge device must be used. In this situation, the system designer is often forced to create a custom board(s) that uses the chosen display bridge, a time-consuming, costly, and laborious task. The CUB display bridge reference design system eliminates that need by providing an out-of-the-box solution.
The CUB system is a series of boards that support either a ‘blue wire’ or direct connection between the CPU and the display. Supporting the entire span of QuickLogic’s ArcticLink III VX product line, the CUB system allows display data to flow from the CPU to the display with all requires interface conversion. The CUB system very closely resembles the actual architecture of mass production devices, allowing the system designer to immediately begin work on creating and testing device firmware and software, speeding time-to-market.
In addition to addressing and solving the necessary display bridging need, the CUB system also features the ability to allow designers to test and evaluate QuickLogic’s VEE (Visual Enhancement Engine) and DPO (Display Power Optimizer) on their own hardware. With simple instructions (via USB) to the CUB, VEE can be demonstrated, adjusted, and even calibrated for the individual system characteristics. Additionally, through manual manipulation of display brightness and the resulting power savings, DPO’s ability to extend system battery life can be proven. Designers are assured, via their own design, of the viewability benefits VEE can provide and can measure actual DPO power savings.
A typical use of the CUB system might occur as follows: a system designer may have a processor board with a RGB display output. However, the chosen display might be a VESA-standard LVDS display. QuickLogic and the customer work to create either a custom PCB board that would plug directly from the processor board’s RGB connector into the CUB main board, or will hand-wire the RGB signal from the processor board directly to the CUB’s Breakout Expansion Card.
The designers VESA-standard LVDS display plugs directly into the existing LVDS Expansion Card.
The entire system is powered up, and after software commands to enable communication between the devices on both the CUB and processor boards, the system designer will be able to pass content directly to the display and can begin work on display tuning and VEE/DPO calibration.
For customers interested strictly in display bridging, the CUB system can be used with the ArcticLink III BX product line, pin-identical to the ArcticLink III VX, but without VEE and DPO.
The CUB system supports all variants of the ArcticLink III VX, including:
|Smartphones, Tablets needing a
MIPI-2 to MIPI-4 bridge
Up to WUXGA
4.5mm x 4.5mm
|VX5AxB||RGB||MIPI||Smartphones, Tablets needing a RGB to MIPI bridge|
|VX5AxD||RGB||LVDS||Tablets needing a RGB to LVDS bridge|
||MIPI||RGB||Smartphones, Tablets needing a MIPI to RGB bridge|
|VX5BxD||MIPI||LVDS||Tablets needing a MIPI to LVDS bridge|
|VX6BxE||MIPI||MIPI & RGB||Smartphones with need to drive either HDMI/MHL transmitter or pico projector
through a MIPI to MIPI & RGB bridge
|VX6BxG||MIPI||LVDS & RGB||Smartphones and tablets with secondary MHL/HDMI output requirement
through a MIPI to LVDS & RGB bridge
|VX6BxH||MIPI||MIPI & LVDS||Smartphones and tablets with secondary MHL/HDMI output requirement
through a MIPI to MIPI & LVDS bridge